Making cable with crimping tools

In cable production process, we have to use some aids and materials production. Here, we first introduce some of these tools and materials. In the production of the project, the most important tool is Crimping Tool of course. Not only the pressure line for personal use, but also this tool Crimping Pliers clamp has a lot of good skills. Fiber optic crimp tool is a tool designed to crimp or connect a connector to the end of a cable. For example, network cables and phone cables are created using a crimping tool to connect the RJ-45 and RJ-11 connectors to the end of the cable. It can bend, cut, strip and crimp insulated wiring in a snap. For cable and phone installation specialists, a handy crimp tool can cut and strip electrical wiring in a few seconds. Fiberstore supplies a wide variety of specialized crimping tools which are all at a very competitive price to help you get the job done right. There are several types of Crimping Tool. Their actual functions and operations are very much the same. The tool has three different functions. Here I will introduce the method of production of cable with a Crimping Tool.

Step 1: we first Crimping Pliers the shear line incision cut out plans need to use the twisted pair length.

Step 2: We need the gray protective layer of the twisted pair off, and can take advantage of the shear line incision Crimping Pliers head scissors Qi, then put the thread the Stripping dedicated knife-edge, slightly clenched Crimping Toolslowly rotating, so that the knife-edge to cut open the twisted-pair protection rubber. Removing part of the protective rubber. Note that this step is crimping tools gear from the stripping knife-edge length is generally just crystal head length, so you can effectively avoid stripping too long or too short. Stripping for too long certainly looks unsightly, on the other hand because of the cable can not be crystal head stuck easy to loose; stripping too short, due to the presence of a protective layer of plastic, can not be fully inserted into the bottom of the first crystal, crystal head pins can not contact intact with the core wire of the cable, of course, can also affect the quality of the line. The stripped gray plastic protective layer can be seen eight core line of four pairs of twisted-pair cable, and you can see the color of each pair are different. Each pair of two core wire is wound by a stained with the corresponding color of the core wire with a little respective colors white and white core wire only soiled. The core wire of the four panchromatic color: brown, orange, green, and blue. Each pair of lines are intertwined with each other, making the network cable must be each of the four pairs of eight thin wires untied, rationalize, Chezhi arranged in neat rows, then in accordance with the provisions of the linear order.

Step 3: we need to each cable are intertwined with each other one by one untied. Unlock after wiring rules according to the needs of several groups of cables arranged in turn and straightened out, arranged, should pay attention to avoid the line winding and overlapping. Cable order and rationalize the cable before intertwined with the cable will have a certain bent, so we should put the cable as far as possible Chezhi keep cable flat flat. Cable straightened method is also very simple, using both hands clutching the cable and then to force the two opposite directions, up and down and pull you can look.

Step 4: we order the cable and straighten out the pressure straight after, you should carefully check again, Crimping Pliers of shear line incision after the top of the cable clipping neatly cropped horizontal directioninsertion, otherwise cable length Soon affect the cable with normal crystal head contact. Previously the protective layer is peeled off too much, you can be here too long thin line bobbed retained remove the outer protective layer about 15mm, the length exactly of the thin wire can be inserted into the respective trough. If the segment is too long to stay, to increase the line of longer interaction twist crosstalk, and secondly crystal head can not suppress the jacket may lead cables emerge from the crystal head, resulting in poor contact or even interrupt line .After cutting, we should try to cables according to tight, and should avoid significant movement or bending the cable, otherwise it may lead to several groups already arranged cutting good cable uneven.

Step 5: we need to do is tidied cable into the crystal head. Note To Crystal head shaping material spring leaf side down, pin up the party, the pins pointing away from the direction one end of the square hole opposite his. At this point, the leftmost 1 feet, the rightmost 8 feet, followed order. Inserted when the need to pay attention to to slowly force 8 cable along eight RJ-45 head trunking insert has been inserted into the top of the trough. Pressure line before the last one from the top of the crystal head check to see whether each group of cable tightly the top end of the crystal head.

Step 6: Of course it is the pressure line to confirm correct after the crystal head into the the Crimping Pliers 8P tank pressure line, insert crystal head, firmly grip pliers if the effort is not enough, you can use both handswith pressure, this pressure process makes crystal head pin protruding outside all pressed into the crystal and head, popping sound can hear a slight force.

That is all of the cable production process. Fiberstore also supplies so many kinds of LAN Network Cable Tester, which are a kind of convenient and comprehensive tool for network professionals. Buy network cable tester, please contact our sales representative right now.